Skip to main content

Christmas Package

Hello! This week, the Stampendous Design Team will be sharing projects that fit the theme, "Dear Santa, I've Been Good!" I used the sweet Christmas Package stencil (which frankly, can be used for plenty of other occasions too!), and a scrap I had leftover from the Chevron Stencil. Check out the full tutorial below.



Supplies:
Stampendous: 
DWLL466: Christmas Package
DWLX7026: Chevron Stencil
MGK01: Fall Micro Glitter Kit
MGK02: Christmas Micro Glitter Kit
DWDGP: Gold Embossing Paste
DWDGWP: Glossy White Embossing Paste
DWDPK: Palette Knife
FX71: Sticky Panels

Other: 
My Colors Cardstock: Dare Devil, Parrot
Molotow: 2mm Round Pen in Signal White
EK Success: Corner Rounder
Beacon Adhesives: Zip Dry

Directions:
1. Tape Christmas Package stencil to Dare Devil cardstock. Tape off the bow so that you don't get paste on it. Paste the box with your Palette Knife and Glossy White Embossing Paste. Remove stencil to wash. While the paste is still wet, sprinkle Lime Micro Glitter from the Halloween Micro Glitter Kit all over. Tap off excess, and allow the box to dry.

2. When the box is completely dry, reapply the stencil, taping off the box this time. Apply Gold Embossing Paste to the bow. Remove and wash stencil, and let the gold paste dry.

3. When the entire package is dry, trim down and round the corners using a corner rounder. Take the Molotow pen and add highlights to the box and bow.


4. Create the card base from Parrot cardstock. Make the card 5 1/2" x 8." Create a faux stitching around the perimeter of the card using the Molotow pen.

5. Using the Chevron stencil and Sticky Panels, take the red and crystal micro glitters from the Christmas Micro Glitter Kit and do the Double Glitter Technique. A video on how to do this technique can be found HERE. The stencil is not as wide as the card base, so figure out the placement of your package, and then slice the Chevron strip. There will be little to no Chevron behind the package, but now it will have the appearance that the strip goes all the way across the card once the package has been glued down.

6. Assemble and glue all pieces with Zip Dry.

Below are the rest of the Stampendous team that will be posting today. Thanks for stopping by. Have an inspiring day!

Comments

Popular posts from this blog

Horse Friends

Hello! This week, the Stampendous team is previewing some of the newest stamps that will be in the 2018 January catalog. You are in for a real treat! There are so many wonderful new images! I had a tough time deciding which to share first, but the beautiful Horse Friends stamp by Laurel Burch won out. I had a fantastic time coloring it, and I couldn't wait to share it with all of you.



Supplies:
Stampendous:
LBP009: Horse Friends

Other:
Imagine: VersaFine Ink in Onyx Black
Bo Bunny: Blueberry Vintage Double Dot Cardstock #12BV807 & Pink Punch Vintage Cardstock #12PPV951
Zig Clean Color Real Brush Markers: 010, 020, 022, 023, 024, 025, 027. 032, 033, 036, 038, 041, 042, 043, 050, 051, 070, 080, 081, 082, 083, 202, 302
Scrapbook Adhesives: EZ-Dots
Canson: Mixed Media Paper
Water Brush


Directions:
1. Stamp Horse Friends on to Mixed Media Paper with VersaFine Ink.

2. Color the stamped image with the colors indicated.

3. Trim the image, leaving a white border.

4. Create the card base w…

Candy Grab: Day 2 of 31

Greetings, Guys & Ghouls! It's Day 2 of the 31 Days of Halloween. Today I have a card that uses a very appropriate stamp for Halloween...it's called Candy Grab and it's from Stampendous. I'm not sure if the skeleton threw them up in the air with joy, or they just fell out of a pinata. But either way, it's a fun stamp! My full instructions on how to recreate this card are below.

Supplies:
Stampendous:
R296: Candy Grab
FREG037: Aged Marine Embossing Powder
FRC20: Hot Lime Fragments

Other:
My Colors Cardstock: Plum
Imagine: Craft Mat, VersaMark Ink, VersaFine Ink in Onyx Black
FaberCastell: PITT Pen- Small
Distress Oxide Inks: Faded Jeans, Wilted Violet, Fired Brick, Peeled Paint, Spiced Marmalade
Canson: Mixed Media Paper
Beacon Adhesieves: Zip Dry Glue
Water Spritzer
Craft Foam
Brush

Directions:

1. Stamp the image with VersaFine ink in Onyx Black on to Canson Mixed Media Paper.

2. Apply Distress Oxide Inks directly to craft mat, using the colors listed.

3. Spritz the i…

Warmest Wishes

Seasons Greetings! This week, the Stampendous team are sharing a few final holiday projects. My card features the delightful Warmest Wishes stamp. I love the vintage feel of the image.

Supplies:
Stampendous:
R300: Warmest Wishes
FRGL02: Twinkle Glitter
FRGL01: Multi Crystal Glitter Mix
DCP1006: Fitted Frames Set B

Other:
My Colors Cardstock: Velvet Night, Evergreen
Zig Clean Color Markers: 010, 022, 034, 036, 038, 041, 044, 060, 062, 64, 065, 070, 091, 092, 095, 097, 230, 302, 901
Imagine: VersaFine Ink in Onyx Black, On Point Glue
Scrapbook Adhesieves: Foam Squares
Canson: Mixed Media Paper

Directions:
1. Stamp the Warmest Wishes stamp on to Mixed Media Paper using Onyx Black VersaFine Ink.

2.Color the image using the Zig Clean Color Markers listed.

3. Apply On Point Glue to areas that you want to have sparkle.

4. Sprinkle the glued areas with Multi Crystal Glitter Mix and let dry.

5. Fussy cut the stamped image.

6. Using Evergreen Cardstock, die cut the Large "R" Fitted Frame.

7. Cr…